|
Isuzu Trooper Owners Club UK™ Isuzu Trooper, Rodeo, Bighorn, Mu & VehiCROSS Owners Club
|
View previous topic :: View next topic |
Author |
Message |
isuzusuzuki ****
Joined: 13 Mar 2012 Posts: 253 Location: hertfordshire
|
Posted: Mon Jun 25, 2012 17:32 Post subject: axle gearbox breathers |
|
|
im going to extend my rear axle breathers because i have had water in there in the past and gearbox breathers, i never had problem on the front axle it is high enough already but will probably do that aswell .Being an isuzu nothing of the self as usaul but have seen some on eebuygum for lawn rovers cheap, does anyone know if these would fit the exsiting holes in the axles, i think the pipe in the kit should fit even if the lawn rover joint isnt the same also where are the breathers on the gearbox.I will probably take a chance on the kit but thought i would ask here first incase anyones know if it will be no good or know of something better. |
|
Back to top |
|
|
Google Sponsor
|
Posted: Mon Jun 25, 2012 17:32 Post subject: Google Ads keep this community free to join! |
|
|
|
|
Back to top |
|
|
gary820 Lifetime member
Joined: 08 Apr 2007 Posts: 2427 Location: Yorkshire
|
Posted: Mon Jun 25, 2012 18:04 Post subject: |
|
|
I use micro sprinkler hose from b and q, 10m roll about £10 Iirc _________________ landcruiser 80 series 4.5, 35's/33's for road, 2inch lift, discreet winch, sliders/armour, factory lockers, stainless side exit +++++ |
|
Back to top |
|
|
gary820 Lifetime member
Joined: 08 Apr 2007 Posts: 2427 Location: Yorkshire
|
Posted: Mon Jun 25, 2012 18:07 Post subject: |
|
|
I just put it into the existing hose from the axle and secure with hoseclip, then just run it into the 1/4 panel behind body lamp. _________________ landcruiser 80 series 4.5, 35's/33's for road, 2inch lift, discreet winch, sliders/armour, factory lockers, stainless side exit +++++ |
|
Back to top |
|
|
isuzusuzuki ****
Joined: 13 Mar 2012 Posts: 253 Location: hertfordshire
|
Posted: Mon Jun 25, 2012 20:30 Post subject: |
|
|
ok thanks where abouts is the gearbox breathers and are they the same size as the axles |
|
Back to top |
|
|
gary820 Lifetime member
Joined: 08 Apr 2007 Posts: 2427 Location: Yorkshire
|
Posted: Mon Jun 25, 2012 20:33 Post subject: |
|
|
There's a sticky in gearbox/transmission bit of the forum that should explain it mate. _________________ landcruiser 80 series 4.5, 35's/33's for road, 2inch lift, discreet winch, sliders/armour, factory lockers, stainless side exit +++++ |
|
Back to top |
|
|
isuzusuzuki ****
Joined: 13 Mar 2012 Posts: 253 Location: hertfordshire
|
Posted: Mon Jun 25, 2012 21:34 Post subject: |
|
|
I have seen that post but the link is not working now |
|
Back to top |
|
|
gary820 Lifetime member
Joined: 08 Apr 2007 Posts: 2427 Location: Yorkshire
|
Posted: Mon Jun 25, 2012 22:23 Post subject: |
|
|
Going off the 3.1 manual (haven't done box on 3.0 yet) I had the panel under centre console out to get to top of box, theres a cylindrical plastic fitting on g/box and t/box (covers the breathers) I pulled those off and used a bit of fuel hose to put onto where plastic bit came off (was a tight fit) then ran a pipe for each one to the bulk head, finished off with a coiled bit with the open end pointing downward.
Hope that makes some sort of sense!!? _________________ landcruiser 80 series 4.5, 35's/33's for road, 2inch lift, discreet winch, sliders/armour, factory lockers, stainless side exit +++++ |
|
Back to top |
|
|
isuzusuzuki ****
Joined: 13 Mar 2012 Posts: 253 Location: hertfordshire
|
Posted: Mon Jun 25, 2012 22:31 Post subject: |
|
|
Thanks will look into that |
|
Back to top |
|
|
|
|
|
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum
|
|