View previous topic :: View next topic |
Author |
Message |
supermotohad *
Joined: 09 Sep 2013 Posts: 15 Location: Surrey
|
Posted: Thu Feb 20, 2014 21:13 Post subject: 3.1td swb bighorn non start |
|
|
Hello there guys is serious need of help before i kill myself.
1995 bighorn short wheel base with the half electronice diesel pump, picked it up drove
500 yards cuts out hasnt run since, replaced ecu, replace diesel pump checked timing and replaced cambelt, cant se to find any software
To plug in please help Hadley |
|
Back to top |
|
|
Google Sponsor
|
Posted: Thu Feb 20, 2014 21:13 Post subject: Google Ads keep this community free to join! |
|
|
|
|
Back to top |
|
|
Gribble *******
Joined: 11 Oct 2007 Posts: 8448 Location: Holset H221W
|
Posted: Fri Feb 21, 2014 0:27 Post subject: |
|
|
Has it got fuel to the injectors ? not much to plug into on a 95 but that bit on the pump was/is for an immobilizer did you put a drive by cable pump on ?
Some more info might help ,anywhere me near are you ? _________________ 2 New Troopers ! |
|
Back to top |
|
|
supermotohad *
Joined: 09 Sep 2013 Posts: 15 Location: Surrey
|
Posted: Fri Feb 21, 2014 0:34 Post subject: |
|
|
Hello mate im in guildford surrey, it does have fuel to the injectors but not alot, i cant find anything that recognises the izuzu all modern software doesnt recognise a diesel izuzu. Nope i replaced the pump with them same that was tested and came
Off a running vehicle as mine is auto and i hear the manual pump conversion isnt fun.
Cheers hadley |
|
Back to top |
|
|
Gribble *******
Joined: 11 Oct 2007 Posts: 8448 Location: Holset H221W
|
Posted: Fri Feb 21, 2014 18:21 Post subject: |
|
|
You won't find anything to read that except a tech one on the transmission there is nothing to read it's an old school engine.
The easy way is to bust off that black plastic case and put 12 volts to the run solenoid. _________________ 2 New Troopers ! |
|
Back to top |
|
|
Grandad *******
Joined: 22 Sep 2005 Posts: 1902 Location: NORFOLK
|
Posted: Fri Feb 21, 2014 19:49 Post subject: |
|
|
This vehicle may be fitted with the electronically controlled drive by wire pump fitted to autos from 95 on if so then it should have the 16 pin obd plug to read the codes jump terminals 4 and 6 turn the ignition on and the check engine light should flash for example one flash short pause then two flashes is 12 = no codes present
the obd plug should be under the centre console by the drivers left foot |
|
Back to top |
|
|
supermotohad *
Joined: 09 Sep 2013 Posts: 15 Location: Surrey
|
Posted: Fri Feb 21, 2014 22:14 Post subject: |
|
|
Stop solonoid works perfectly and i cant seem to find any codes. I have diesel but doesnt seem to be enough pressure to open the injectors i dont know what else to try. |
|
Back to top |
|
|
Gribble *******
Joined: 11 Oct 2007 Posts: 8448 Location: Holset H221W
|
Posted: Fri Feb 21, 2014 22:59 Post subject: |
|
|
You have changed the fuel filter and bled the housing ? what ecu did you change I'm puzzled _________________ 2 New Troopers ! |
|
Back to top |
|
|
supermotohad *
Joined: 09 Sep 2013 Posts: 15 Location: Surrey
|
Posted: Fri Feb 21, 2014 23:00 Post subject: |
|
|
Yeah all bled, mines the *beep* half electric pump model |
|
Back to top |
|
|
Gribble *******
Joined: 11 Oct 2007 Posts: 8448 Location: Holset H221W
|
Posted: Fri Feb 21, 2014 23:23 Post subject: |
|
|
You can't see the solenoid if you got the black cover that's why it's called an immobiliser _________________ 2 New Troopers ! |
|
Back to top |
|
|
supermotohad *
Joined: 09 Sep 2013 Posts: 15 Location: Surrey
|
Posted: Fri Feb 21, 2014 23:56 Post subject: |
|
|
Mine doesnt have an immobiliser im guessing because. Iv had the solonoid out. Only codes
I can read are 21 and 34, can this shed an light? Clutching at straws.com |
|
Back to top |
|
|
Grandad *******
Joined: 22 Sep 2005 Posts: 1902 Location: NORFOLK
|
Posted: Sat Feb 22, 2014 0:57 Post subject: |
|
|
21 is accelerator position sensor circuit the sensor is on the pedal
24 is vehicle speed sensor or Vss circuit
you say you changed the ecu so those codes may be from the other vehicle as although the codes can clear if disconnected from a power source it's not always the case |
|
Back to top |
|
|
supermotohad *
Joined: 09 Sep 2013 Posts: 15 Location: Surrey
|
Posted: Sat Feb 22, 2014 1:06 Post subject: |
|
|
That is a good point how can the codes be cleared other than disconnecting the battery? Am i right in saying 34 is map sensor? If so would this stop it from running? Cheers for
Your help guys |
|
Back to top |
|
|
Grandad *******
Joined: 22 Sep 2005 Posts: 1902 Location: NORFOLK
|
Posted: Sat Feb 22, 2014 1:32 Post subject: |
|
|
code 34 is control sleeve sensor or MAP sensor circuit
it shouldn't be the control sleeve as you took the pump from a running vehicle
can you try the map sensor off the same vehicle you took the pump from? |
|
Back to top |
|
|
supermotohad *
Joined: 09 Sep 2013 Posts: 15 Location: Surrey
|
Posted: Sat Feb 22, 2014 14:34 Post subject: |
|
|
Dont currently have the other vehicle local got
The parts from a breakers |
|
Back to top |
|
|
Grandad *******
Joined: 22 Sep 2005 Posts: 1902 Location: NORFOLK
|
Posted: Sun Feb 23, 2014 0:10 Post subject: |
|
|
The map will not stop the engine running or starting |
|
Back to top |
|
|
|